Essential Plumbing Tips for Installing a Bathtub
Essential Plumbing Tips for Installing a Bathtub
Blog Article
In this article in the next paragraph you can locate more very good points around Tools You Need to Install a New Bathtub .
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can relocate quickly; if you need to open up a wall surface to remove the old bathtub and also place the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the job as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one before you start. Chances are you might need an expert plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your washroom if you have actually already acquired a new bathtub and also don't require to transform the setup of your previous supply of water pipelines.
Your devices and also material checklist need to consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the limited accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washing machines are in location in between the faucet and the sink. Safeguard the tap in place with the maker supplied backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The former kind needs to be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Making use of the two wooden boards under its feet, place the tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the tub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the same for the various other tap.
Activate the water supply and also inspect all joints as well as new pipework for leaks and also tighten them if necessary. Fill up the bathtub as well as also check the overflow electrical outlet and the typical outlet for leaks.
Finally, repair the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub must wait until the bathtub has been used at least once as this will settle it into its final setting.
Getting ready for the Installation
Firstly, the supporting framework supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to permeate the wall surface between the bath as well as the tiling, resulting in complications with dampness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealant can split fairly very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is recommended to fit the tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of content was a smart idea. I beg you set aside a second to distribute this write-up if you enjoyed reading it. Thanks a bunch for your time. Visit us again soon.
Get answers now! Report this page